How do I access my pfSense web interface?

To access the pfSense webconfigurator, open a web browser on a computer connected to your firewall and enter https://[your LAN IP address]. By default, it is 192.168. 1.1. Enter your username and password in the login page.

Does pfSense have a web interface?

Most pfSense® software configuration is performed using the web-based GUI. There are a few tasks that may also be performed from the console, whether it be a monitor and keyboard, over a serial port, or via SSH.

How do I access pfSense from command line?

PFSense – Enable Console Login

Open a browser software, enter the IP address of your Pfsense firewall and access web interface. The Pfsense web interface should be presented. On the prompt screen, enter the Pfsense Default Password login information. After a successful login, you will be sent to the Pfsense Dashboard.

What is opt interface in pfSense?

OPT. OPT or Optional interfaces refer to any additional interfaces other than WAN and LAN. OPT interfaces can be additional LAN segments, WAN connections, DMZ segments, interconnections to other private networks, and so on.

How do I reset pfSense?

Factory Default from the GUI

  1. Navigate to Diagnostics > Factory Defaults.
  2. Review the items on the page which will be affected by the reset.
  3. Click. Factory Reset.
  4. Click OK to confirm the action and start the reset process.

How do I connect to pfSense router?

Connecting your new pfSense router to the network

  1. Unpack the box and take out the router.
  2. Connect the network cables.
  3. Connect the power adapter.
  4. APU board is booting.
  5. Connect to the web interface.
  6. Use a different NordVPN server.

How do I change my LAN IP with pfSense?

How to edit the pfSense® LAN IP address

  1. Connect to the serial console.
  2. Edit the assigned network interfaces.
  3. Choose a new IP address.
  4. Choose an appropriate subnet bit count.
  5. Confirm the upstream gateway address.
  6. Ignore IPv6.
  7. Leave the DHCP server disabled.
  8. Decide the protocol for web interface access.

Which is better pfSense vs mikrotik?

pfSense offers significant flexibility and powerful features, but it is also a heavier piece of software compared to RouterOS. Businesses looking for the lightest possible software that can run on very low power machines may prefer Mikrotik’s firewall solution.

Is pfSense a good firewall?

[pfSense] is [a] combination of firewall and router features. This is very good product [compared] to others open source firewall. If you [lack a] budget for firewall then you should go with this firewall. [pfSense] provides you basic security as well as routing features.

What is the default login for pfSense?

The default credentials for a pfSense® software installation are: Username. admin. Password.

How do I remotely access pfSense SSH?

Enable SSH via GUI

  1. Navigate to System > Advanced, Admin Access tab.
  2. Check Enable Secure Shell.
  3. Set SSHd Key Only to Public Key Only to allow only key-based SSH authentication.
  4. Enter a port number in SSH Port if the SSH daemon should listen on a non-default port. Leave the field blank for the daemon to use port 22.
  5. Click Save.

What Shell does pfSense use?

The PHP shell is a powerful utility that executes PHP code in the context of the running system. As with the normal shell, it is also potentially dangerous to use. This is primarily used by developers and experienced users who are intimately familiar with both PHP and the pfSense software code base.

How many interfaces can pfSense have?

Should a particular environment require more than 128 interfaces, consider alternate designs that do not involve using all of the interfaces on the firewall directly. If the firewall must handle large numbers of interfaces, be wary of potential performance and GUI concerns.

What is opt port on router?

OPT port means optional port. It is used for the system administrator to set as one zone of WAN, LAN 1, LAN 2, DMZ or WLAN. Hence, this port is very flexible for the administrator to design their network topology.

What is IGB interface?

Description. The igb Gigabit Ethernet driver is a multi-threaded, loadable, clonable, GLD-based STREAMS driver supporting the Data Link Provider Interface, dlpi(7P), on Intel 82575 Gigabit Ethernet controllers.

How do I reinstall pfSense?

Reinstalling pfSense CE

  1. Go to to download the latest image of pfSense® Community Edition (CE) software.
  2. Write the image to a USB memstick.
  3. Connect to the console port of the device.
  4. Insert the memstick into an open USB port and boot the system.

How do I reset OPNsense?

Since OPNsense password protects its console menu by default, you will need to enter “Single User” mode to reset the root password.

  1. Power off the Vault.
  2. Attached a monitor and keyboard or COM cable to the Vault.
  3. Power on the Vault and allow OPNsense to boot.

How can I reset my pfSense password?

2 Answers

  1. Reboot the pfSense box.
  2. Choose option 4 (Single User Mode) from the loader menu (The one with the ASCII pfSense logo)
  3. Press enter when prompted to start /bin/sh.
  4. Remount the drive as rewritable: /sbin/mount -o rw /
  5. Run the built-in password reset command:
  6. Follow the prompts to reset the password.

Can pfSense be used as a router?

pfSense is mostly used as a router and firewall software, and typically configured as DHCP server, DNS server, WiFi access point, VPN server, all running on the same hardware device.

How do I run pfSense on Raspberry Pi?

pfSense doesn’t have an official release for Raspberry Pi, it’s only available on AMD64 architecture, so there is no way to install it on a Raspberry Pi. Other solutions can be used instead to turn a Raspberry Pi into a router firewall.

Can pfSense manage access points?

With a wireless card that supports hostap mode (See Cards Supporting Access Point (hostap) Mode), pfSense® software can be configured as a wireless access point.

Where do I go in the pfSense to configure an IP address on an interface?

pfsense changing LAN interface IP and DHCP Range

How do I use OPNsense?

Installation of OPNsense 21.7

  1. Select the USB flash drive as boot device in the BIOS.
  2. SSH connection to OPNsense or log in locally on the console (user installer, password opnsense).
  3. Confirm Keymap Selection.
  4. Select Other Modes.
  5. To install on a single disk, select Auto (UFS).
  6. Select target disk.

How do I reserve an IP address in pfSense?

Top Menu: Services > DHCP Server >> LAN (Tab)

At the end of the General Options section, specify an IP range so that part of that range is free so that pfsense can use the unused range to allocate static IPs.

Is OPNsense better than pfSense?

Comparison Results: OPNsense ultimately won out in this comparison. Our reviewers agree that OPNsense is easy to install and easy to use, while pfSense was less so. One area where pfSense did come out on top was in the free support category. The GUI is helpful, but it’s not user-friendly.

Why should I use pfSense?

pfsense has many features and advanced capabilities that ensure it always follows either default or custom rules. It also filters traffic separately whether it’s coming from your internal network of devices or the open internet, allowing you to set different rules and policies for each.

Which is better MikroTik vs Ubiquiti?

Both offer routers, switches, hotspot devices, and management software to manage and control the network. In general, MikroTik offers more granular flexibility at the cost of usability, while Ubiquiti offers a smoother, albeit more rigid, user experience.

Is pfSense better than SonicWall?

pfSense has low system requirements and can scale quite comfortably. Compared to the SonicWall, any modern VMWare host loaded with pfSense has overkill requirements past what SonicWall can do (minus the UTM portion). The Sonic Wall tops out (SMB wise) at dual core 500 Mhz proc. Handles up to 100+ mbps of VPN traffic.

How much RAM do I need for pfSense?

1 GB should be considered a minimum but some configurations may need 2 GB or more, not counting RAM used by the operating system, firewall states, and other packages.

Is pfSense a next generation firewall?

There are a variety of successful open-source firewalls, like pfSense software, OPNSense, IPFire, etc. They are quite stable firewall solutions and have a handful of features, commercial-grade performance, timely updates, and great community support.

See also  Defending Your Network Against the Unknown
Hi, I'm Nam Sun-Hi. My first name means: "One with a joyful demeanor." I'm a Korean student and author at I spend all my time either writing or studying. I love learning new things, and I think that's why I enjoy writing so much - it's a way of learning more about the world around me.